Synthesis,structure, CO oxidation,and H2 production activities of CaCu3−xMnxTi4−xMnxO12 (x = 0, 0.5, and 1.0)

Synthesis of nanocrystalline pristine and Mn-doped calcium copper titanate quadruple perovskites, CaCu_3?xMn_xTi_4?xMn_xO₁₂ (x = 0, 0.5, and 1.0) by modified citrate solution combustion method has been reported. Powder X-ray diffraction patterns attest the phase purity of the perovskite materials. Average particle sizes of all the materials obtained from the Scherrer's formula are in the range of 55–70 nm. The specific surface areas for all the perovskites obtained from BET isotherms are found to be low as expected for the condensed oxide systems and fall in the range of 13–17 m² g^?1. Transmission electron microscopy studies show a reduction in particle size of CaCu₃Ti₄O₁₂ with increase in Mn doping. Ca and Ti are present in +2 and +4 oxidation states in all the materials as demonstrated by X-ray photoelectron spectroscopy analyses. Cu²⁺ gets reduced in CaCu₃Ti₄O₁₂ with higher Mn content. Mn is observed to be present only in +3 oxidation state. All the materials have been examined to be active in CO oxidation as well as H₂ production from methanol steam reforming. CaCu₃Ti₄O₁₂ with ~14 at.% Mn is found to show best catalytic activities among these materials. A comprehensive analysis of the catalytic activities of these perovskites toward CO oxidation and H₂ production from MSR reveal the cooperative activity of copper-manganese in the doped perovskites and it is more effective at lower manganese content.     

Tribological mechanism of micro-arc oxidation coatings prepared by different electrolyte systems in artificial seawater

The micro-arc oxidation (MAO) coatings were prepared in four different electrolyte systems, including mixed acid, phosphate, phosphate-aluminate and phosphate-silicate electrolytes. The friction and wear properties of MAO coatings in ambient air, seawater and four groups of saline solutions related to seawater were investigated. The results showed that the addition of silicate to phosphate could increase the density of the coating. The phosphate-aluminate ceramic layer exhibited the lowest wear rate in various environments. Additionally, the friction coefficient and wear rate of MAO coating in seawater were lower than those in ambient air, which was due to the boundary lubrication effect of seawater. Meanwhile, the presence of divalent metal salts in seawater made its lubricity better than other salt solutions.     

Effect of post heat-treatment on the microstructure and high-temperature oxidation behavior of precipitation hardened IN738LC superalloy fabricated by selective laser melting

The present study investigated the effect of as-built and post heat-treated microstructures of IN738LC alloy fabricated via selective laser melting process on high temperature oxidation behavior.The as-built microstructure showed fine cell and columnar structure due to high cooling rate.Ti element segrega-tion was observed in inter-cell/inter-columnar area.After post heat-treatment,the initially-observed cell structure disappeared,instead bimodal Ni3(Al,Ti)particles formed.High temperature(1273 K and 1373 K)oxidation test results showed parabolic oxidation curves regardless of temperature and initial microstructure.The as-built IN738LC fabricated via the selective laser melting process displayed oxida-tion resistance similar to or slightly better than that of IN738LC fabricated via wrought or cast process.Heat-treated SLM IN738LC,although had similar oxidation weight-gain values to those of the SLM as-built material at 1273 K,showed relatively better oxidation resistance at 1373 K.Bimodal Ni3(Al,Ti)precipitate formed in the post heat treatment changed the local chemical composition,thereby led to changes in alumina former/chromia former location and fraction on the alloy surface.It was concluded that in heat-treated IN738LC increased alumina former fraction was found,and this resulted in excellent oxidation resistance and relatively low weight-gain.     

Reconstructed Water Oxidation Electrocatalysts: The Impact of Surface Dynamics on Intrinsic Activities

Electroreduction of small molecules such as H₂O, CO₂, and N₂ for producing clean fuels or valuable chemicals provides a sustainable approach to meet the increasing global energy demands and to alleviate the concern on climate change resulting from fossil fuel consumption. On the path to implement this purpose, however, several scientific hurdles remain, one of which is the low energy efficiency due to the sluggish kinetics of the paired oxygen evolution reaction (OER). In response, it is highly desirable to synthesize high-performance and cost-effective OER electrocatalysts. Recent advances have witnessed surface reconstruction engineering as a salient tool to significantly improve the catalytic performance of OER electrocatalysts. In this review, recent progress on the reconstructed OER electrocatalysts and future opportunities are discussed. A brief introduction of the fundamentals of OER and the experimental approaches for generating and characterizing the reconstructed active sites in OER nanocatalysts are given first, followed by an expanded discussion of recent advances on the reconstructed OER electrocatalysts with improved activities, with a particular emphasis on understanding the correlation between surface dynamics and activities. Finally, a prospect for clean future energy communities harnessing surface reconstruction-promoted electrochemical water oxidation will be provided.     

Nitrogen Removal Performance of Denitrifying Ammonium Oxidation System in Treating Sulfamethoxazole-laden Secondary Wastewater Effluent

In this study,nitrogen removal performance of the denitrifying ammonium oxidation(DAO)process was investigated when treating sulfamethoxazole(SMX)-laden secondary wastewater effluent.The influent SMX concentration showed negligible effect on efficiencies for removal of nitrate and COD.However,the ammonium ions removal rate was moderately reduced,when the influent SMX concentration in wastewater reached 6 mg/L.Total nitrogen removal efficiency remained as high as 76.77%towards the day 158 at the end of experiment.Candidatus_Brocadia and Candidatus_Kuenenia were the functional anammox strains.The unclassified_f__Rhodobacteraceae sp.was predominant heterotrophic denitrifying strain in the studied reactor.The concentrations of soluble extracellular polymeric substances in sludge obviously increased from 16.76 mg/g VSS to 32.31 mg/g VSS,which might protect the nitrogen removal strains from high-concentration SMX.This result provides a theoretical and technical foundation for the application of denitrifying ammonium oxidation process in treating sulfamethoxazole-laden secondary wastewater effluent.     

Structural characteristics and high-temperature oxidation behaviour of nano-HfO2-doped thermal barrier coatings

The uneven growth of thermally grown oxides (TGOs) in thermal barrier coating systems is an important cause of cracking failure at the coating interface in high-temperature environments. The doping of rare earth elements in the bonding layer can effectively inhibit the formation of spinel oxides in the TGO and improve the high-temperature oxidation resistance of the coating. However, a single rare earth element has a limited effect on inhibiting TGO failure. In this study, a NiCoCrAlYHf coating was prepared using a supersonic flame spraying (HVOF) technique. The effects of HfO₂ doping on the high-temperature oxidation behaviour of the coatings and diffusion behaviour of metallic elements in the coatings were investigated at 1100 °C. The results showed that the nano-sized HfO₂ filled the pores between the powder particles and improved the hardness of the coating. During the high-temperature oxidation process, the oxides formed by Hf and Y had a large size and low solubility, which effectively blocked the diffusion of Al. This slowed the generation of spinel oxides, effectively inhibited the growth of the TGO, it inhibits the initiation and propagation of cracks within the coating, reduces damage to the coating from tensile and compressive stresses at the interface, and improved the high-temperature oxidation resistance of the coating.     

Effect of malondialdehyde oxidation on structure and physicochemical properties of amandin

Oil, accounting for 45% of almonds, is easily oxidised and can further induce the protein oxidation to reduce their quality. Structure and physicochemical properties of amandin, the main water-soluble protein in almonds, inducing oxidation by malondialdehyde (MDA) were investigated. The results showed that the content of carbonyl group increased from 5.23 to 33.25 nmol mg⁻¹ of protein with the increase in MDA concentration (P < 0.05). However, the sulphydryl content, surface hydrophobicity, particle size and the absolute value of ζ-potential first increased and then decreased. Fourier-transformed infrared spectroscopy (FT-IR) confirmed that the structure of amandin changed from order to disorder. Fluorescence spectroscopic analysis revealed that mild oxidation (0–0.1 mmol L⁻¹ MDA) exposed hydrophobic groups of the protein. Sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) suggested that protein oxidation promoted crosslinking between protein molecules. Furthermore, protein oxidation markedly declined the total amino acid content of amandin (P < 0.05). In conclusion, MDA oxidation changed the structure and amino acid content of amandin, and caused the protein aggregate and crosslink through hydrophobic interaction and electrostatic interaction.     

High-temperature behavior of oxide dispersion strengthening CoNiCrAlY

To fabricate oxide dispersion strengthened bond coatings, commercial Co–30wt-%Ni–20Cr–8Al–0?4Y powder was milled with 2% additions of Al₂O₃, Y₂O₃ or Y₂O₃ + HfO₂. Low-pressure plasma sprayed, free-standing specimens were oxidised in air + 10%H2O at 1100 °C both isothermally (100 h) and in 500, 1?h cycles. Dry air cyclic testing conducted at both ORNL and FZJ showed remarkably similar results. In general, the water vapour addition caused more scale spallation. Two LPPS specimens without oxide additions were tested for comparison. The specimens with 2%Al₂O₃ addition exhibited the best behaviour as the powder already contained 0?4%Y. Additions of 2%Y₂O₃ and especially 1%Y₂O₃ + 1%HfO₂ resulted in over-doping as evidenced by high mass gains and the formation of Y- and Hf-rich pegs. Scanning transmission electron microscopy of the isothermal specimens showed no Hf and/or Y segregation to the alumina scale grain boundaries in the over-doped specimens.     

Fabrication of 3D Ni nanosheet array on Crofer22APU interconnect and NiO-YSZ anode support to sinter with small-size Ag nanoparticles for low-temperature sealing SOFCs

A novel low-temperature sealing method was developed to seal solid oxide fuel cells. The 3D Ni nanosheet array was pre-fabricated on faying surfaces of Crofer22APU interconnect and NiO-YSZ anode-support. Then it was covered with Au film without changing its morphology. This special nanostructure improved sintering efficiency between Ag nanoparticles and substrates. A dense joint was obtained at the low-temperature between 250 °C–300 °C. This method effectively avoided the oxidation of interconnect during sealing. When joints were sealed at 300 °C, the shear strength reached 16 MPa. The fracture was mainly located in the central Ag layer, presenting a significant plastic deformation. Due to the effective protection of Ni layer, joints also possessed excellent oxidation resistance in oxidizing atmosphere at 800 °C for 400 h. After high-temperature oxidation, the shear strength was increased to 23 MPa, revealing an increasement of 43.8% compared with the as-sealed condition (16 MPa). This sealing method has great potential in sealing solid oxide fuel cells. It also can be extended to seal other energy-conversion devices.     

Hot corrosion studies of a salt-coated Ni-based superalloy under flowing wet air and sulfur vapor ambient

Corrosion of a salt-coated Ni-superalloy has been studied at 900°C under a wet air and sulfur vapor ambient. The corrosion thickness, after an incubation of ~60 hr, linearly increases with the corrosion time t and the onset of surface spallation occurred at t ≈ 60 hr. The corroded layer consists of a corrosion front dominated by Cr₃S₄ scales and linear precipitate structures, an inner corrosion layer dominated by Ni₃S₂ and NiO, and an outer corrosion layer dominated by Al₂O₃ networks surrounding the Ni₃S₂ and/or NiO scale structures. The corrosion mechanism is discussed based on the coexistence of H₂O, sulfur, and oxygen.